Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Northeast Philadelphia?
Chimney liner and rebuild work in Northeast Philadelphia typically runs from about $2,400 to $6,800 for a stainless steel liner installation, and about $6,500 to $22,000 for a full masonry rebuild. Most Northeast Philadelphia homeowners with a standard single-flue rowhouse chimney end up spending somewhere between $3,200 and $5,400 to reline, while a rebuild on an older twin or porch-front home with a failing stack often lands in the $9,000 to $16,000 range.
Those numbers are estimates, and the written estimate we give you after looking at your flue and your masonry is what sets the final price. If you want to know where your chimney falls on that spread before anything is ordered, call (855) 658-4023. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
We’re a full-system chimney specialist, which matters on this page more than on most. Relining and rebuilding are the two jobs where a general handyman runs out of depth and a sweep-only company refers you elsewhere. We handle both, and we work with trade-grade liner products – DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco and Copperfield – because the right liner for your flue is a product decision, not a guess. Your chimney handles heat, gas, and debris – it deserves a specialist, not a generalist.
Key Takeaways
- Stainless steel liner installation in Northeast Philadelphia: roughly $2,400 to $6,800, and most jobs sit between $3,200 and $5,400.
- HeatShield clay liner resurfacing, when the existing tile can be saved: roughly $1,600 to $3,400, a lower-cost route than a full reline on the right flue.
- Full masonry rebuild: roughly $6,500 to $22,000 depending on how much of the stack is coming down.
- Our technicians have up to 13 years of experience, and the local pro is licensed and insured as their state requires.
- Estimates are free and the written estimate is what you pay.
Chimney Liner & Rebuild Cost Breakdown (2026)
Here’s how the two jobs break down by line item for the Northeast Philadelphia market in 2026. Liner and rebuild are very different purchases, so we’ve kept them separate rather than averaging them into one misleading number.
| Line item | Typical estimated range | What it covers |
|---|---|---|
| Chimney inspection (video scan) | $0 – $350 | Camera scan of the flue, crown and firebox; free when bundled with liner work |
| Flexible stainless steel liner (DuraFlex) | $2,400 – $4,800 | Single-flue retrofit in a typical Northeast Philly rowhouse, insulated, with top plate and cap |
| Liner for a two-flue or oversized flue | $4,200 – $6,800 | More liner length, secondary flue, or a larger appliance connection |
| HeatShield clay liner resurfacing | $1,600 – $3,400 | Deteriorating clay tile relined from the inside without demolition |
| Liner for a gas or oil appliance vent | $1,900 – $3,600 | Sized and rated for the appliance, with proper termination |
| Partial rebuild (upper stack, above roofline) | $6,500 – $11,000 | Rebuilding the chimney from the roofline up, new crown, new cap |
| Full rebuild (ground to crown) | $11,000 – $22,000 | Tear-down and rebuild of the full stack, including flashing tie-in |
| New crown and cap | $700 – $1,800 | Cast crown, multi-flue cap, and the seal that keeps water out |
| Firebox and damper repair (paired with liner work) | $600 – $2,200 | Firebox repointing, damper replacement, smoke chamber parging |
The liner number swings most on flue shape and length. A straight vertical flue in a Porch Front rowhouse takes a flexible DuraFlex liner with very little fuss. An offset flue, a chimney that’s been parged down to a smaller opening, or a two-story twin with a long run all add material and labor. On the rebuild side, the cost driver is how far down the damage goes. Water that’s been getting in at the crown for years eats the mortar joints at the top first, and a partial rebuild above the roofline handles that. Once the damage reaches the flashing line or the interior wythe, you’re into a full rebuild whether anyone wants that or not.
One thing that surprises people: the estimate for liner work often includes a few small items that a cheaper quote leaves out. Top plates, a properly sized cap, and insulation around the liner all affect how the system performs. A liner without those is a cheaper job, not a better one.
What Affects Chimney Liner & Rebuild Pricing in Northeast Philadelphia
- Housing age and original construction. Much of Northeast Philadelphia was built in tight waves – Mayfair, Holmesburg, Tacony, Rhawnhurst, Bustleton – and the chimneys that came with those houses were built for coal or for a single wood stove, not for a modern insert or a gas appliance. Retrofitting a liner into a flue that was never meant for that appliance takes more sizing work, and that’s where the DuraFlex flexible liner earns its place: it fits a flue that a rigid liner can’t navigate.
- Roofline and access. A porch-front rowhouse with the chimney shared between neighbors changes how the crew sets up and how much they can work from above. Steep pitched roofs and chimneys set back from the ridge add setup time. Access affects the labor half of any estimate in Northeast Philadelphia, and it’s the part homeowners can’t see from the ground.
- Flue condition and tile integrity. If the clay tile is cracked through, a stainless liner is the fix. If the tile is intact but the joints are eaten, HeatShield resurfacing can save the chimney without demolition. We use HeatShield because it solves a specific problem – a deteriorating clay liner – in a way that most sweep-only companies simply can’t offer. That decision alone can move your cost by a couple thousand dollars, in your favor.
- Degree of masonry damage. Repointing a few courses, rebuilding the top ten feet, or replacing the whole stack are three very different jobs. The gap between them is where most of the rebuild cost spread lives.
- Water intrusion from the crown and flashing. A cracked crown lets water into the masonry every time it rains, and Philadelphia’s freeze-thaw winters turn that water into spalling brick and crumbling mortar. Crown and flashing work done early costs a fraction of the rebuild it prevents. This is the single most common reason a chimney that “looked fine” needs rebuilt masonry.
- Damper, firebox and smoke chamber. A liner is only as good as what surrounds it. If the firebox needs repointing or the damper won’t seat, it makes sense to do that work in the same visit rather than pay for two mobilizations. We do fireplace repair alongside chimney work so there’s one point of accountability from the firebox to the crown.
Is It Cheaper to Repair or Replace a Chimney Liner in Northeast Philadelphia?
Repairing is almost always cheaper than replacing when the clay tile is still sound – HeatShield resurfacing runs about $1,600 to $3,400 versus $2,400 to $6,800 for a full stainless reline. Replacing with a stainless liner is the right call when the tile is cracked through, when the flue has been resized, or when you’re connecting a new appliance that needs a specific liner rating. A video inspection tells you which situation you’re in before any money is committed.
Resurfacing isn’t a shortcut. It’s a product-specific fix for a specific failure, and it only works when the tile is intact enough to hold it. When it’s the right answer it saves real money. When it isn’t, a stainless liner is the durable choice, and we’ll tell you which one you’re looking at rather than upselling the bigger job.
How to Save on Chimney Liner & Rebuild
The biggest savings in this trade come from sequencing, not from shopping quote to quote. Here’s what’s worth doing:
- Get a video inspection before you get quotes. A camera scan ($0 to $350, often included when you book liner work) tells every contractor the same thing, so you’re comparing real prices instead of guesses. It also stops a cheap quote from quietly turning into a bigger job mid-project.
- Bundle fireplace repair with liner work. Firebox repointing, a damper, and the liner share one setup. Doing them together costs less than three separate visits.
- Fix the crown before it becomes a rebuild. The most expensive chimney repair in Northeast Philadelphia is the one caused by water that got in for a decade. A crown and cap job in the hundreds prevents a rebuild in the thousands.
- Don’t chase the lowest liner number. A quote that leaves out insulation, a top plate, or a proper cap isn’t a discount – it’s a shorter job that you’ll pay for again later. Compare what’s included, not just the total.
- Ask about material choice. The right liner for your flue is the one rated for your appliance and sized to your flue. That’s a technical call, and it’s one we’ll walk through with you.
Estimates are free, and the price we quote in writing is the price. Call (855) 658-4023 to get the inspection booked. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
When Do You Need a Chimney Rebuild Instead of a Repair?
You need a rebuild when the masonry itself is failing – spalling brick, mortar joints gone soft through the depth of the wall, a chimney that’s leaning or separating from the house, or water damage that’s reached the flashing line. Repointing and a new crown handle surface damage. A rebuild is structural.
The signs to watch for in an older Northeast Philadelphia home are usually visible from the ground or the living room. Crumbling mortar at the roofline, brick faces flaking off, a white powdery stain on the masonry, or a chimney that’s pulling away from the wall are all signals the stack is losing integrity. Inside the house, a damper that no longer seals, rust on the firebox, or smoke that won’t draw straight up are signals the flue is compromised. None of these improve on their own. If you’re seeing any of them, it’s worth having the chimney looked at before the next heating season. You can read more about the options on our chimney liner & rebuild page, or start with a routine chimney sweep Northeast Philadelphia visit that includes an inspection.
What Does a Chimney Rebuild Involve?
A rebuild means taking the masonry down and putting it back correctly. The crew removes the damaged section – or the entire stack – lays new brick and mortar, rebuilds the flue transition, installs a new crown, and sets a cap on top. The liner goes in during the rebuild rather than after, which is why a rebuild plus liner costs less than the two jobs done separately. Flashing where the chimney meets the roof gets redone at the same time, because that’s the other place water gets in.
Expect a rebuild to take several days of on-site work, depending on how much of the stack is coming down and how the crew can access the roof. A partial rebuild above the roofline moves faster than a full stack. We schedule the work around weather, and a written estimate tells you exactly which scope you’re buying.
What About a Gas or Oil Appliance?
A gas or oil flue is sized and rated differently from a wood flue, and the liner has to match the appliance. A liner installed for wood and then used with a gas appliance is the wrong product, and it’s a safety issue. If you’re switching appliances or you’ve just bought a house with an unfamiliar setup, part of the inspection is confirming what’s actually venting into the flue. That’s true across Northeast Philadelphia, where a lot of homes have had their heating changed over the years without anyone documenting it.
This is where full-system knowledge matters. Olympia Chimney and DuraFlex liner lines cover wood, gas, and oil applications with different ratings, and picking the right one is the whole job. We work with those products regularly, alongside Gelco and Famco for the surrounding components.
FAQs – Chimney Liner & Rebuild Cost
How much does chimney liner installation cost in Northeast Philadelphia?
Chimney liner installation in Northeast Philadelphia typically costs $2,400 to $6,800, with most single-flue rowhouse jobs landing between $3,200 and $5,400. The final number depends on flue length, flue shape, and whether the job needs a two-flue setup or an oversized liner. Call (855) 658-4023 for an exact quote – estimates are free.
How much does a full chimney rebuild cost in Northeast Philadelphia?
A full chimney rebuild in Northeast Philadelphia runs about $11,000 to $22,000, while a partial rebuild above the roofline costs roughly $6,500 to $11,000. The difference comes down to how far down the damage goes and how much masonry is coming out. Call (855) 658-4023 for an exact quote – estimates are free.
Is it cheaper to repair or reline a chimney?
Repairing is cheaper when the clay tile can be saved – HeatShield resurfacing runs about $1,600 to $3,400 versus $2,400 to $6,800 for a full stainless reline. Relining is the right call when the tile is cracked through or the flue needs a different rating. Call (855) 658-4023 for an exact quote – estimates are free.
Can you come today?
Same-day service is often possible, and we book inspections into the next opening when today is full. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. Call (855) 658-4023 for an exact quote – estimates are free.
Do you need a permit for a chimney rebuild in Northeast Philadelphia?
Most cities require a permit for structural chimney work, and Philadelphia is no exception for a rebuild that changes the masonry or the flue. Your city’s building department is the authority on what your specific job needs, and we’ll walk you through that as part of the written estimate. Call (855) 658-4023 for an exact quote – estimates are free.
How long does a chimney liner last?
A properly installed stainless steel liner is a long-term fix, and the lifespan comes down to the product rating and how well it matches the appliance. A liner rated for wood but used with gas, or a liner that’s undersized for the flue, won’t last as long as one chosen for the application. The right liner for your flue is the one we’ll recommend in writing. Call (855) 658-4023 for an exact quote – estimates are free.
What’s the difference between a liner and a rebuild?
A liner is the flue lining that sits inside the chimney; a rebuild replaces the masonry structure itself. Liner work typically runs $2,400 to $6,800, and a full rebuild $11,000 to $22,000. Many jobs need both at once, and doing them together costs less than two separate projects. Call (855) 658-4023 for an exact quote – estimates are free.
Why Homeowners Choose a Full-System Specialist
Most chimney companies either sweep and refer out the heavy work, or rebuild masonry and hand off the flue. That split costs you time and puts two contractors on one system with no one accountable for the whole thing. We cover sweeping, cap and crown work, liner installation, full rebuilds, and fireplace repair as one scope, because the failure at the crown and the failure at the firebox are usually connected. Our technicians have up to 13 years of experience, and we’re HeatShield-certified for liner resurfacing – a proprietary process that requires specific product training. That’s not a marketing line; it’s the difference between a company that knows the product and one that’s reading the label.
If your chimney has been giving you trouble, the cheapest route is usually to have it looked at before the next cold snap. Call (855) 658-4023 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Northeast Philadelphia market as of 2026. Chimney Sweep Northeast Philadelphia offers free estimates – call (855) 658-4023.
Written by the team at Chimney Sweep Northeast Philadelphia.
What Our Customers Say
"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
- Bethany Meyer"Cap keeps the birds out now, which after two springs of scratching noises is worth every penny."
- Kevin Reed"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Craig Mercer