Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Liner & Rebuild for Northeast Philadelphia Homeowners
A failed liner doesn’t announce itself. You might notice a faint smell on a damp day, a bit of crumbling tile inside the flue, or white staining bleeding through the brick above the roofline. Northeast Philadelphia has a lot of older rowhouses and twin homes in Bustleton, Rhawnhurst, and Olney where the original clay tile liner has been quietly taking on heat, moisture, and acidic flue gas for decades. When that tile goes, the chimney can no longer do its one job safely.
Our technicians have up to 13 years of experience with liners and rebuilds, and we work with professional-tier brands like DuraFlex, HeatShield, and Gelco because the material matters as much as the install. We offer same-day availability in Northeast Philadelphia when the schedule allows. Call (855) 658-4023 to get on the book. We answer 24/7.
What Our Chimney Liner & Rebuild Service Includes
Every job starts with a camera inspection so we can see the flue from the firebox to the crown. Nothing gets recommended until you’ve seen what we see. From there, here’s what each piece of the work looks like.
Stainless Steel Liner
A stainless steel liner is a rigid or semi-rigid pipe inserted into the flue to give smoke and gas a sealed path out of the house. You need one when the existing clay tile has cracked, offset, or missing joints, or when a new appliance requires a correctly sized flue. We size the liner to the appliance and the flue, then insulate it so the system drafts properly and stays within safe temperature limits. The result is a liner you can inspect and trust for a long time.
Flexible Liner
A flexible liner is the workhorse for older Northeast Philadelphia homes with offsets, bends, or an irregular flue that a rigid pipe won’t navigate. DuraFlex flexible stainless is what we reach for when the flue path isn’t straight, letting us line the chimney without tearing into the masonry. It’s often the difference between a reasonable repair and a full demolition, which matters in this housing stock.
Liner Replacement
Liner replacement means pulling the failed tile or old liner and installing a new one. You’re a candidate when the tile is spalled, the joints are open, or a previous liner has been damaged by heat or a chimney fire. We remove the old material, inspect the surrounding masonry, and install a new stainless system sized for what you actually burn. This is the single most important safety upgrade for an older chimney.
Partial Rebuild
A partial rebuild addresses the damaged section of the chimney above the roofline, where freeze-thaw cycles punish brick and mortar the hardest. You need it when the top courses are loose, spalling, or leaning, but the structure below is sound. We rebuild that section, reset or replace the crown, and tie the work back into the existing stack. Keeping a partial repair partial is how you avoid paying for masonry you didn’t need.
Full Chimney Rebuild
A full rebuild is for a chimney that has lost structural integrity, from the foundation on up, or where water has rotted the stack through. You’ll know because the chimney leans, the mortar is failing throughout, or it’s been abandoned and unsafe for years. We take it down and rebuild the full stack with proper flashing, crown, and a liner ready for service. It’s a big job, and we only recommend it when a repair genuinely won’t hold.
Liner Repair
Liner repair fixes a liner that’s still mostly sound but has localized damage, gaps, or cracking. HeatShield resurfacing is our go-to for deteriorating clay tile liners that don’t yet need full replacement; it’s a proprietary process that requires specific product training, and it lets us restore a clay flue from the inside. When the liner is past saving, we’ll say so plainly and talk through replacement instead of patching a problem that will come back.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Liner & Rebuild
We work with professional-tier chimney brands because a liner is only as good as the material behind it. DuraFlex flexible stainless is what we lean on for retrofits where the flue path bends or offsets, and we know where those systems hold up and where they fail. Gelco gives us reliable options for the masonry and crown side of the work, and we’ve seen how its products behave over a Northeast Philadelphia winter.
HeatShield is the specialty piece: a liner resurfacing system for deteriorating clay tile that many sweep-only companies simply don’t offer. It’s a product-specific process, and getting it right takes training and experience with the material. Whether you already have a HeatShield job in place, a DuraFlex liner, or a Gelco product on the crown, we can service it. And whether you have one of these brands or any other make, we can help. The brand matters less than whether the installation was done correctly for your flue.
Signs You Need Chimney Liner & Rebuild Right Now
- Crumbling tile or debris in the firebox. Broken pieces of clay tile showing up at the bottom of the firebox mean the liner above is failing. That’s a direct path for heat and gas into the surrounding framing, so it’s worth a look soon.
- White staining on the brick above the roof. Efflorescence is moisture pushing salts out of the masonry, often a sign that water is getting in around a failing crown or liner. Left alone, it works deeper into the brick each season.
- A smoky smell when the fireplace isn’t burning. That’s the chimney failing to draft properly, often because the flue is undersized, blocked, or the liner is compromised. It’s a sign the system isn’t venting the way it should.
- Visible cracks in the chimney exterior. Cracks in the brick or mortar above the roofline let water in and let heat escape in ways you can’t see from the ground. A camera inspection tells you whether the damage stops at the surface or goes deeper.
- A chimney that leans or has loose top courses. Movement at the top of a chimney points to structural trouble underneath. That’s the kind of thing that needs eyes on it before another freeze-thaw season makes it worse.
Our Chimney Liner & Rebuild Process – Step by Step
- 1
Inspection and camera scan. We start at the firebox and work up the flue with a camera, then check the crown, flashing, and cap from the roof. You get to see what the camera sees, so nothing is a mystery.
- 2
Written findings and a clear recommendation. We put the findings in writing, lay out what actually needs doing, and tell you plainly when a repair can safely wait. You’ll get a written estimate before anything is booked.
- 3
Sizing and material selection. We match the liner to your appliance and flue size, then choose the material – DuraFlex for a difficult flue path, HeatShield for resurfacing a failing clay tile, stainless for a full replacement. This is where product knowledge saves you from a liner that drafts poorly or wears out early.
- 4
Installation. We pull what’s failed, prep the flue, and install the new liner or rebuild the masonry as planned. Insulation, terminations, and the crown all get handled so the system is sealed from the firebox to the top.
- 5
Final check and documentation. We verify the draft, confirm the fit, and give you photos of the finished work. You’ll know exactly what was done and what to watch for going forward.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Northeast Philadelphia?
A typical stainless steel liner installation in Northeast Philadelphia runs roughly $2,500 to $5,500 depending on flue height, liner size, insulation, and whether the flue needs prep work first. A liner repair or HeatShield resurfacing generally runs in the hundreds to low thousands, well under the cost of a replacement when the tile is still serviceable. A partial rebuild above the roofline typically starts around $2,000 and climbs with the height and extent of damage, and a full chimney rebuild is the largest line item, often $8,000 and up when the full stack comes down.
What moves those numbers: flue height and accessibility, whether the chimney sits on a pitched roof or a flat one, the condition of the masonry around the flue, and the liner material. To avoid overpaying, ask for the camera findings in writing and get a written estimate before any work is booked, so the scope is clear and the price is set per job. Every estimate includes the inspection, the camera scan, and photos you can review yourself.
| Service | Typical Estimated Range |
|---|---|
| Stainless steel liner installation | $2,500 – $5,500 |
| Liner repair or HeatShield resurfacing | $600 – $2,000 |
| Partial rebuild (above roofline) | $2,000 – $6,000 |
| Full chimney rebuild | $8,000 and up |
The written estimate sets the final price. Call (855) 658-4023 for an exact quote; estimates are free.
Chimney Liner & Rebuild Near Northeast Philadelphia – Our Service Area
We work throughout Northeast Philadelphia and the surrounding communities, including Bustleton, Rhawnhurst, Olney, Rockledge, Lower Moreland, Abington, Bensalem, Feasterville, Trevose, McKinley, and Lower Southampton. Response times vary by schedule and location, and we’ll give you a window when you book. For more on keeping the flue clean between bigger jobs, see our chimney sweep Northeast Philadelphia page. If you’re nearby, we also handle chimney liner & rebuild in Rockledge and chimney liner & rebuild in Lower Moreland.
Serving Northeast Philadelphia, PA – Our Local Coverage Area
We serve Northeast Philadelphia and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Liner & Rebuild in Northeast Philadelphia
It’s the repair or replacement of the flue liner that carries smoke and gas out of your home, plus any masonry work on the chimney structure itself. The liner protects the surrounding wood framing from heat and keeps combustion gases contained; the rebuild restores the brick and crown above the roofline. We handle both under one roof, along with the chimney liner & rebuild work that ties them together. Call (855) 658-4023 to schedule an inspection.
A stainless steel liner installation is usually a one-day job, while a HeatShield resurfacing or liner repair often takes a bit less. A partial rebuild can run a couple of days, and a full rebuild takes longer depending on the extent of the work. We’ll give you a realistic timeline with your written estimate, not a guess. Call (855) 658-4023 for a clear picture of what your job involves.
A stainless liner typically runs $2,500 to $5,500, liner repair starts in the hundreds to low thousands, and a full rebuild starts around $8,000. The final price depends on flue height, material, and masonry condition, and the written estimate sets it. Call (855) 658-4023 for an exact quote; estimates are free.
Yes, we work with DuraFlex, HeatShield, Gelco, and Copperfield, along with Olympia Chimney and Famco. We service and install these systems and know where they wear out, so we can tell you whether a repair or replacement makes sense. Whether you have one of these brands or another make, we can help. Call (855) 658-4023 to talk through what you have.
We offer same-day availability in Northeast Philadelphia when the schedule allows. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday, with Saturday closed. A call outside dispatch hours gets booked into the next opening. Call (855) 658-4023 to find the soonest slot.
Warranty terms on liner and rebuild work are confirmed with your written estimate, so you’ll know exactly what’s covered before we start. We’ll walk you through the coverage that applies to your materials and job. Call (855) 658-4023 to ask about warranty on your specific project.
Clear the area around the fireplace and hearth, and make sure we can reach the chimney from the roof and from the ground. If you have a gas appliance, know its make and model, since that helps us size the liner correctly. After that, we handle the inspection and the work. Call (855) 658-4023 with any questions before we arrive.
Schedule Your Chimney Liner & Rebuild Service in Northeast Philadelphia Today
Whether you’re seeing crumbling tile, a smoky smell, or white staining on the brick, the next step is a camera inspection so you know what you’re dealing with. We’ll show you what we find, put it in writing, and tell you honestly when work can wait. Call (855) 658-4023 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Northeast Philadelphia.